GPSUNDERGROUND FORUM IS ON SALE
Results 1 to 10 of 10

Thread: speedtraps 2010

  1. #1
    JeeBee is offline Master Sergeant
    Join Date
    May 2010
    Posts
    141
    Thanks
    6
    Thanked 20 Times in 10 Posts

    Question speedtraps 2010

    Does anybody has a link to the new speedtraps cd's ? it is a total of 3 cd's.

  2. #2
    Join Date
    Jul 2010
    Posts
    4
    Thanks
    7
    Thanked 0 Times in 0 Posts

    Re: speedtraps 2010

    check your pn

  3. #3
    gazo is offline Global Moderator
    Join Date
    May 2010
    Posts
    5,630
    Thanks
    14
    Thanked 2,665 Times in 188 Posts

    Re: speedtraps 2010

    Would you consider giving the links here instead of private messaging?
    We are on a forum remember?
    All questions should be directed through the forum
    Private messages will be disregarded

  4. #4
    Join Date
    Jul 2010
    Posts
    4
    Thanks
    7
    Thanked 0 Times in 0 Posts

    Re: speedtraps 2010

    Code:
    http://netload.in/dateibJ45cqT30V/BSTS2010E.rar.htm
    Ciao
    Last edited by PlutoniC; 9th August 2010 at 08:36.

  5. #5
    gazo is offline Global Moderator
    Join Date
    May 2010
    Posts
    5,630
    Thanks
    14
    Thanked 2,665 Times in 188 Posts

    Re: speedtraps 2010

    All questions should be directed through the forum
    Private messages will be disregarded

  6. The Following User Says Thank You to gazo For This Useful Post:


  7. #6
    emsef is offline Staff Sergeant
    Join Date
    Jul 2010
    Location
    UK
    Posts
    96
    Thanks
    23
    Thanked 63 Times in 9 Posts

    Re: speedtraps 2010

    How do I use this?

    So far I have:
    1. burned CD successfully
    2. insert into my Becker
    3. brief "loading" message

    Then... no difference to operation?

    Any ideas? I am running Becker V5.

  8. #7
    gazo is offline Global Moderator
    Join Date
    May 2010
    Posts
    5,630
    Thanks
    14
    Thanked 2,665 Times in 188 Posts

    Re: speedtraps 2010

    Loading takes a few seconds and after that you will be warned at every speed camera position when routing is active
    The explanation is included with every cd

    And after you shut down and start again you will have to reload the cd again. It will not "remeber" that you have loaded the speedcam data
    All questions should be directed through the forum
    Private messages will be disregarded

  9. #8
    Join Date
    Jul 2010
    Posts
    4
    Thanks
    7
    Thanked 0 Times in 0 Posts

    Re: speedtraps 2010

    And without active routing you will be warned (beep) at every speed camera position (Cascade 7944).
    All data are stored in the memory, to reset this data -> System Setup -> Reset Function -> Reset Settings => yes
    After install remove cd and after shut down / restart all speedcam data are available.
    Only limitation is you can not run all three cd`s at the same time.

  10. #9
    gazo is offline Global Moderator
    Join Date
    May 2010
    Posts
    5,630
    Thanks
    14
    Thanked 2,665 Times in 188 Posts

    Re: speedtraps 2010

    It seems to depend on the model, the version or the fact that the battery voltage falls below a minimum level during engine start
    It is also explained in the readme files that reloading after shut down may be required on some occasions

    On Cascade and Traffic Pro 7945/7949:
    Audible warnigns are issued even without routing. Symbols only appear during active routing and only while in Navigating or radio mode. Not if a sub-menu is activated!
    Also the CD must be taken out of the drive.
    Last edited by gazo; 7th September 2010 at 12:13.
    All questions should be directed through the forum
    Private messages will be disregarded

  11. #10
    TIK
    TIK is offline Sergeant
    Join Date
    May 2011
    Posts
    50
    Thanks
    0
    Thanked 8 Times in 7 Posts

    Speed limit tool

    now we have a tool to de-/encode *.lwd files
    supported are all known lwd-files:
    • Becker speed limit data (within navi CF iso image)
    • speed cam data from various sources (speedtraps, Peugeot WIP, ...)

    what is possible with this tool:
    • Modify speed limits on navi CF (add / delete)
    • Modify speed cam data (add / delete)
    • Merge speed cam and speed limit data to be integrated in navi iso image

    now there is no need for a speed cam CD anymore
    furthermore it's a new feature for Mexico owners (units without CD drive).

    just to keep one source: here is the link to the speedlimit_tool

    btw: many thanks to mira308sw for *.lwd decoding
    Last edited by TIK; 10th June 2012 at 02:46.

  12. The Following 2 Users Say Thank You to TIK For This Useful Post:


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •