Announcement

Collapse
No announcement yet.

Help unbricking Mio Moove M300

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Help unbricking Mio Moove M300

    Hello!

    I have a problem with above mentioned GPS. When you power it on, the the screen shows that you have to connect it to a computer. So i did and started Mio More Desktop to try reinstall the software. But that option was grayed out. so I made a backup of a working Moove M300, and copy it in the defective one. But during file transfer the unit god disconnected, and now its stuck on orange Mio loading screen. Now there is no USB connection. I tried draining the battery and then connect it to USB but no go. I managed to enter the service mode by connecting the ground with 9th pin on the flash chip. But how to navigate through that menu? Bare in mind that Moove M300 does not have a SD slot, nor any buttons only a power slider switch, and it has integrated 2gb flash.

    Regards Ivan

  • #2
    Re: Help unbricking Mio Moove M300

    metalac666 GpsPasSion Forums - How to upgrade/downgrade the firm. on Mio (Moov+C) 1)Download program DNW 2)Download firmware for Moov300 3)Device coupled to the computer 4)DNW runs on your computer and choose obtiunea transmit files firmware of computer...5)Choose obtiunea ... wince upgrade USB (Format)----------After rewriting, do hardreset, sizing screen and a backup copy directly into Flash...Ciao
    Last edited by gyany; 26th September 2012, 13:17.

    Comment


    • #3
      Re: Help unbricking Mio Moove M300

      Have had the same problem with MIO MOOVE 200

      -----------------
      ZIPPYSHARE

      RAPIDSHARE
      -----------------


      INSTRUCTION

      1. Format SD card to FAT and copy Cobia_300_32 to root folder on SD card

      2. Open sat nav , take out mainboard and remove metal parts which cover chipsets

      3. Inside you should see TSOP 48 NAND FLASH. Connect permanently pin no.19 (write
      protect) with pin no. 12 (VCC) .Next I make short-circuit pin. 9 with GND in different
      moments when I turn on sat nav (SD Card inside).

      4. After few moments sat nav was reading files from SD card. You should get 2 options :
      USERMODE and SUPERMODE. Choose first one, click OK then restart your MIO.

      5. You should see blue service screen.

      It was working for me on MIO MOOVE 200. I have tried many times with success.
      Last edited by Sebo_; 26th September 2012, 13:25.

      Comment


      • #4
        Re: Help unbricking Mio Moove M300

        Originally posted by gyany View Post
        metalac666 GpsPasSion Forums - How to upgrade/downgrade the firm. on Mio (Moov+C) 1)Download program DNW 2)Download firmware for Moov300 3)Device coupled to the computer 4)DNW runs on your computer and choose obtiunea transmit files firmware of computer...5)Choose obtiunea ... wince upgrade USB (Format)----------After rewriting, do hardreset, sizing screen and a backup copy directly into Flash...Ciao
        That does not help me because I don't have USB connection with the device. TY for your reply.

        Originally posted by Sebo_ View Post
        Have had the same problem with MIO MOOVE 200

        -----------------
        ZIPPYSHARE

        RAPIDSHARE
        -----------------


        INSTRUCTION

        1. Format SD card to FAT and copy Cobia_300_32 to root folder on SD card

        2. Open sat nav , take out mainboard and remove metal parts which cover chipsets

        3. Inside you should see TSOP 48 NAND FLASH. Connect permanently pin no.19 (write
        protect) with pin no. 12 (VCC) .Next I make short-circuit pin. 9 with GND in different
        moments when I turn on sat nav (SD Card inside).

        4. After few moments sat nav was reading files from SD card. You should get 2 options :
        USERMODE and SUPERMODE. Choose first one, click OK then restart your MIO.

        5. You should see blue service screen.

        It was working for me on MIO MOOVE 200. I have tried many times with success.
        As I mentioned Moove M300 has no SD card slot only 2gb internal memory. TY for your reply.

        Comment


        • #5
          Re: Help unbricking Mio Moove M300

          metalac666 DNW program has two drivers that make USB connection

          Comment


          • #6
            Re: Help unbricking Mio Moove M300

            Originally posted by gyany View Post
            metalac666 DNW program has two drivers that make USB connection
            I will give it a shot. That should work even if the unit is not recognized by the PC?

            Comment


            • #7
              Re: Help unbricking Mio Moove M300

              yes..Install one of two drivers

              Comment


              • #8
                Re: Help unbricking Mio Moove M300

                I've got the VERY SAME PROBLEM as metalac666. Where can i download DNW program?

                Comment


                • #9
                  Re: Help unbricking Mio Moove M300

                  Download file - FriendlyARM or Downloads - FriendlyARM
                  I realy do not know how to use it. Simply,i am unable to make usb connection ((((

                  Comment

                  Working...
                  X