Announcement

Collapse
No announcement yet.

speedtraps 2010

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • speedtraps 2010

    Does anybody has a link to the new speedtraps cd's ? it is a total of 3 cd's.

  • #2
    Re: speedtraps 2010

    check your pn

    Comment


    • #3
      Re: speedtraps 2010

      Would you consider giving the links here instead of private messaging?
      We are on a forum remember?
      All questions should be directed through the forum
      Private messages will be disregarded

      Comment


      • #4
        Re: speedtraps 2010

        Code:
        http://netload.in/dateibJ45cqT30V/BSTS2010E.rar.htm
        Ciao
        Last edited by PlutoniC; 9th August 2010, 08:36.

        Comment


        • #5
          Re: speedtraps 2010

          http://netload.in/index.php?id=10&fi...2033&captcha=1

          This one works!
          All questions should be directed through the forum
          Private messages will be disregarded

          Comment


          • #6
            Re: speedtraps 2010

            How do I use this?

            So far I have:
            1. burned CD successfully
            2. insert into my Becker
            3. brief "loading" message

            Then... no difference to operation?

            Any ideas? I am running Becker V5.

            Comment


            • #7
              Re: speedtraps 2010

              Loading takes a few seconds and after that you will be warned at every speed camera position when routing is active
              The explanation is included with every cd

              And after you shut down and start again you will have to reload the cd again. It will not "remeber" that you have loaded the speedcam data
              All questions should be directed through the forum
              Private messages will be disregarded

              Comment


              • #8
                Re: speedtraps 2010

                And without active routing you will be warned (beep) at every speed camera position (Cascade 7944).
                All data are stored in the memory, to reset this data -> System Setup -> Reset Function -> Reset Settings => yes
                After install remove cd and after shut down / restart all speedcam data are available.
                Only limitation is you can not run all three cd`s at the same time.

                Comment


                • #9
                  Re: speedtraps 2010

                  It seems to depend on the model, the version or the fact that the battery voltage falls below a minimum level during engine start
                  It is also explained in the readme files that reloading after shut down may be required on some occasions

                  On Cascade and Traffic Pro 7945/7949:
                  Audible warnigns are issued even without routing. Symbols only appear during active routing and only while in Navigating or radio mode. Not if a sub-menu is activated!
                  Also the CD must be taken out of the drive.
                  Last edited by gazo; 7th September 2010, 12:13.
                  All questions should be directed through the forum
                  Private messages will be disregarded

                  Comment


                  • #10
                    Speed limit tool

                    now we have a tool to de-/encode *.lwd files
                    supported are all known lwd-files:
                    • Becker speed limit data (within navi CF iso image)
                    • speed cam data from various sources (speedtraps, Peugeot WIP, ...)

                    what is possible with this tool:
                    • Modify speed limits on navi CF (add / delete)
                    • Modify speed cam data (add / delete)
                    • Merge speed cam and speed limit data to be integrated in navi iso image

                    now there is no need for a speed cam CD anymore
                    furthermore it's a new feature for Mexico owners (units without CD drive).

                    just to keep one source: here is the link to the speedlimit_tool

                    btw: many thanks to mira308sw for *.lwd decoding
                    Last edited by TIK; 10th June 2012, 02:46.

                    Comment

                    Working...
                    X